A rubble stone foundation is a wall of field or quarried stone laid in lime mortar, the standard way Toronto houses were built before poured concrete took over in the early 1900s. Most of them are still carrying their houses. The work they need is usually one of three things: repointing and drainage to keep water and soil out of the joints, underpinning to gain height or new bearing, or benching where the old wall should be touched as little as possible. A licensed engineer decides which, and the City of Toronto requires a permit and engineer testing on every underpinning job.
If you own a Victorian or Edwardian house in Leslieville, Riverdale, Cabbagetown, Corktown, Parkdale or the older streets of the Junction and the Annex, there is a good chance the basement wall you are looking at is stone. This page covers how to tell, why stone behaves differently from the poured walls most underpinning advice assumes, what each repair route involves, and what it costs on the figures this site publishes. For the neighbourhood view of the same houses, see our post on underpinning in Leslieville and Riverdale.
We coordinate foundation work. We do not perform structural engineering, and we will not tell you from a photo or a phone call whether your stone wall is sound, how deep it can go, or what a crack in it means. Those are an engineer's calls, made on site.
Rather just talk?
(289) 207-6470Tell us your basement perimeter and current ceiling height and we can give you a realistic range on the call.
- A firm, itemized price up front
- Permits and engineering in the number
- The real timeline, honestly
Get a real range
Not a brochure. Tell us the basics and we will come back with numbers that reflect your actual foundation.
How to tell if your foundation is rubble stone
Go to the basement and look at the outside walls where nothing covers them. A rubble foundation shows irregular stones of different sizes, with wide mortar joints between them and no straight courses. Some are rough fieldstone, rounded from the ground they came out of. Others are roughly squared quarried stone. Either way, it does not look like the smooth grey face of poured concrete or the regular grid of concrete block.
Three things often hide it:
- Parging. A coat of cement render over the inside face, sometimes painted. Look where the parging has cracked or come away, usually low on the wall or behind the furnace.
- A brick wall above. Many Toronto houses of this age have stone below grade and brick from about grade up, so the part you see outside is brick and the part you see in the basement is stone.
- A finished basement. Drywall and studs over the stone. A utility room or the space under the stairs is usually left bare.
The thickness gives it away too. Stone foundation walls are far thicker than a modern poured wall, which you can see at a basement window opening.
Why stone is a different engineering case
Most underpinning advice, including most of what is on this site, assumes a poured concrete or block foundation on a defined footing. A rubble wall breaks that assumption in four ways, and each one changes what the engineer does before anyone digs.
There is often no separate footing. The bottom of the wall may simply be wider stones set in a trench. Underpinning means building a new footing below something that may not have a clear underside to work from.
The wall is not uniform. Stone size, mortar condition and wall thickness change along a single wall. An engineer cannot assume the bearing behaviour of one section tells them about the next, which is why the Leslieville and Riverdale post says each section gets judged on its own.
The mortar is lime, not cement. Lime mortar is softer and more porous than the stone around it. That is by design: the mortar is the sacrificial part, it lets moisture move through the wall, and it is the part that gets repointed every few generations. When people repoint a stone wall with hard cement mortar, the stone ends up taking the stress the mortar used to take. Parks Canada's Standards and Guidelines for the Conservation of Historic Places, published on HistoricPlaces.ca, lists repointing "with mortar of a higher Portland cement content than in the original mortar" as not recommended, because the bond can end up stronger than the stone and damage it, and recommends pointing mortars weaker than the masonry units.
Water finds the joints. A stone wall below grade has hundreds of mortar joints, and over a century groundwater washes the lime out of the ones on the outside face. That is where most rubble foundation problems start: damp walls, sand on the floor at the base of the wall, loose stones. It is a drainage and mortar problem first, which is why it overlaps so heavily with basement waterproofing in Toronto.
A stone wall that has stood for 120 years is not a weak wall. It is a wall built to a different logic, and the repair has to follow that logic or it creates the next problem.
The three routes: repoint, underpin or bench
Rubble foundation questions usually start from one of three situations. The wall is damp or losing mortar, they want more ceiling height, or a home inspector has written "stone foundation, monitor" in a report. Those lead to different jobs.
1. Repointing, parging and drainage
If the goal is a drier, sounder wall at the same height, the work is on the joints and the water. Deteriorated mortar is raked out by hand and the joints are repointed with a lime-based mortar matched to the original. On the outside, the usual fix is excavating along the wall, repointing or parging the outside face, and installing a membrane and drainage so water is carried away instead of sitting against the stone. The exterior waterproofing figure published on this site, $150 to $350 per linear foot, is the right order of magnitude for the excavation-and-membrane part. The masonry repair itself is quoted after someone has seen how far the mortar has gone.
This route does not gain any headroom. It is often the right one for a house where the basement is storage and laundry and will stay that way.
2. Underpinning a rubble foundation
Underpinning a stone wall is the same basic method as any other: dig under the wall in short numbered sections, pour new concrete footing and wall beneath it, let it cure, and move on to the next section, never leaving long runs unsupported. What changes is the work before the first section is dug.
On a rubble wall the engineer typically wants to see the wall's condition along its length, decide how the stone will be supported while each section is open, and decide what happens to loose or hollow sections above the new concrete. The section lengths and sequence on the drawings reflect what they find. That assessment is why rubble jobs tend to sit toward the upper end of the engineering range, and it is a poor place to save money.
The City of Toronto's Residential Underpinning application guide, read at source this month, sets the rules that apply:
- Drawings must show the stages of the underpinning, numbered to show the sequence of work, with the lineal metres proposed.
- A Professional Engineer must design and review the foundation on site when it goes below the footing of an adjacent building and within the soil's angle of repose. On a Victorian semi or row house, that is the shared wall.
- On every underpinning job, engineered or not, the owner has to retain a Professional Engineer for testing and reports at the first and last stages of construction in order to pass inspections.
- A Commitment to General Reviews form, signed by the owner and the engineer, is required where the adjacent-footing condition applies, where the underpinning exceeds 1200 mm of laterally unsupported height, or where the soil is clay or silt.
How much height any of this gains is the engineer's design, not a promise anyone can make before the assessment. What height a legal suite needs, and how to measure what you have now, is on our page about basement lowering in Toronto.
3. Benching instead
Benching leaves the old wall and footing where they are, digs the middle of the floor down, and builds a concrete bench around the perimeter to hold the soil under the original foundation. On a stone wall that is the appeal: far less disturbance to the century-old masonry. The trade is floor width, since the bench takes roughly two feet off each side.
On this site's published figures benching runs 20 to 40 percent less than underpinning the same basement. Whether the remaining width is a room you would use is a measurement you can do yourself; our benching vs underpinning page walks through it. Whether benching is structurally appropriate for your particular stone wall is, again, the engineer's call.
Rubble foundations in semis and row houses
Most of Toronto's stone foundations sit under semis and rows, so the wall you share with the neighbour is usually stone too, and it is carrying both houses. That brings in the adjacent-footing rule above on almost every job, a party wall conversation before the drawings are final, and in many cases sequencing that keeps the shared wall supported at every stage. None of that is unique to stone, but stone makes the engineer more conservative about it. The full picture is on underpinning a semi-detached house in Toronto.
What it costs, on published figures
We do not publish a separate price for rubble foundations, because the difference is in the engineering and the masonry condition, not in a different rate. What applies is the same set of published figures as any Toronto job:
| Item | Published figure | Note for a stone foundation |
|---|---|---|
| Underpinning | $500 to $750 per linear foot of wall | Stone jobs often sit toward the upper half because of the extra section-by-section work |
| Engineering | $1,500 to $8,000 | The pre-dig assessment of a rubble wall pushes this toward the upper end |
| City permit fee | $12.37 per linear metre of underpinning, $214.79 minimum (2026) | Verified on the City's fee schedule this month |
| Exterior waterproofing | $150 to $350 per linear foot | The drainage side of a repoint-and-drain job |
| Repointing and masonry repair | Quoted after inspection | Depends entirely on how much mortar has gone |
As an illustration on those published rates, not a quote: 100 linear feet of underpinning comes to $50,000 to $75,000 for the underpinning line alone, plus engineering, plus a City permit fee of about $377 (30.5 metres at $12.37), plus HST. The full breakdown of what moves a Toronto total is on our underpinning cost page, and what the engineer's fee covers is on the underpinning engineer page.
What to do before you call anyone
- Look at the wall and take a few photos of bare stone, damp patches and any sand at the base. They help the first conversation, even though they will not settle any structural question.
- Measure slab to joist in two or three places, so you know what height you start from.
- Decide what the basement is for. Storage, a family room and a legal suite lead to three different jobs.
- Check the permit history. If someone has already underpinned part of the wall, the City's permit records may show it, and that changes the plan.
- Get the engineer in before the quotes. On a stone foundation more than any other, contractors pricing different assumptions produce quotes you cannot compare. Our permits page covers the order of operations.
Common questions
What is a rubble stone foundation?
A foundation wall built from field or quarried stone laid in lime mortar, without regular courses. It was the standard way to build in Toronto before poured concrete became common in the early 1900s, so it is found mostly under Victorian and Edwardian houses in the older parts of the city.
Can a rubble stone foundation be underpinned?
Usually, yes. The method is the same short, numbered sections as any underpinning job. What changes is the engineer's assessment before digging, because stone walls are not uniform and often have no separate footing. Whether your particular wall can be underpinned, and how, is decided by the engineer on site.
Should a stone foundation be repointed with cement mortar?
Generally not. The federal Standards and Guidelines for the Conservation of Historic Places advise against repointing with mortar of a higher Portland cement content than the original, because the bond can end up stronger than the stone. Lime-based mortar matched to the original is the usual recommendation.
Why is there sand on my basement floor along a stone wall?
Often it is lime mortar that water has washed out of the joints over time. That is a sign to have the wall looked at and the drainage checked. We will not tell you from a description whether it is serious; an engineer or experienced masonry contractor should see it.
Is a house with a rubble foundation a bad buy?
Not on that fact alone. Many Toronto houses stand on stone foundations that have carried them for over a century. What matters is the wall's condition, the water management around it and any past work, which is why an inspection and the permit history matter more than the material.
Does underpinning a stone foundation need a permit in Toronto?
Yes. Underpinning always needs a City building permit, numbered stage drawings, and engineer testing and reports at the first and last stages of construction. A Professional Engineer's design and site review is also required where the work goes below an adjacent footing within the soil's angle of repose.
How much does it cost to underpin a rubble foundation in Toronto?
The published rate is $500 to $750 per linear foot of wall, plus engineering at $1,500 to $8,000, the City permit fee and HST. Stone jobs tend to sit toward the upper half of both ranges because of the extra assessment. A firm total comes only after the engineer's design.
Call (289) 207-6470 with the age of the house, whether it is a semi, a row or detached, and what you want the basement to become, or send the details below. We will tell you which of the three routes your project is likely to follow and arrange the engineer's assessment.
Rather just talk?
(289) 207-6470Tell us your basement perimeter and current ceiling height and we can give you a realistic range on the call.
- A firm, itemized price up front
- Permits and engineering in the number
- The real timeline, honestly
Get a real range
Not a brochure. Tell us the basics and we will come back with numbers that reflect your actual foundation.